Buy ASTM D REDLINE Standard Specification for Filament-Wound Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks from SAI. Dec 2, One of the most com- monly used specifications for filament- wound FRP tanks is ASTM D This standard was first published in and. For Filament Wound Fabrications: ASTM D Specification for Filament Wound Glass. Fiber Reinforced Thermoset Resin Chemical Resistant Tanks.

Author: Goltisho Mezigrel
Country: Somalia
Language: English (Spanish)
Genre: Finance
Published (Last): 13 November 2004
Pages: 175
PDF File Size: 4.95 Mb
ePub File Size: 19.55 Mb
ISBN: 891-2-84812-227-4
Downloads: 68887
Price: Free* [*Free Regsitration Required]
Uploader: Kakus

Resources & News

Only those constructions evaluated for design properties in For the convenience of the user, Committee D has highlighted those changes that may impact the use of this test method. Hold-down lugs should be grouted or shimmied to prevent excessive loads being transferred to the tank shell. D — Nozzle Inside Diameter Up to 10 in.

Successive layers shall uniformly increase in width in that speci? A number in parentheses indicates the year of last reapproval. Rub a few drops of acetone on the laminate surface until it evaporates. Methods of manufacture that incorporate stiffening bands as a means of knuckle stabilization, are permissible alternatives by agreement between purchaser and fabricator, provided the fabricator v document the validity of the design.

This specification does not address the design of vessels intended for pressure above atmospheric, vacuum conditions, except as classified herein, or vessels intended for use with liquids heated above their flash points. The interior overlay shall present the same corrosion resistance to the?

NOTE 20—A useful technique to check the cure of a non-molded surface of a polyester resin is as follows: It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Soft-soled shoes should be worn by workmen entering the tank. PD t 5 2S 8 shell, or to join the bottom or top head to the shell, the thickness of the structural joint overlay shall be determined by the following equation, but shall not be ast, than 3?

TOP Related Posts  BECKY Y MINNIE VAN DE COMPRAS SOPHIE KINSELLA PDF

While Design Tanks has elected not to seek certification at asgm time, we meet and exceed many of the RTP-1 standards without the additional costs associated with certification.

Fluid level in the tank is an important consideration in the analysis. This specification covers cylindrical corrosion-resistant tanks made of commercial-grade glass-fiber-reinforced polyester or vinylester thermoset resin fabricated by filament winding for above-ground vertical installation, to contain aggressive chemicals at atmospheric pressure as classified herein. Contact-molded laminates shall satisfy the minimum property requirements listed in Speci?

Suitable methods include use of ultraviolet absorbers, incorporation of pigment of sufficient opacity in the outer surface resin-rich layer, or use of resins inherently resistant to ultraviolet degradation. Tolerances on installation are shown in Fig. Tanks can be moved by positioning fork-lift trucks on either side of the tank with forks padded.

Prior to hoisting the top end, a suitable protection pad of material should be placed under the bottom pivot point of tank so that as the tank rises, the strain is taken on the pad. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? The thickness of a joint overlay near the knucle radius tangent line of a dished head contributes to the knucle reinforcement.

Design Tanks complies with the design strength requirements of ASTM Dutilizing a rigorous in-line and end-of-line quality control process plus testing of all resins and incoming materials. Type II tanks may also require additional reinforcement. The cradles or skid shall be padded and secured to the bed of the vehicle in such a manner that will prevent damage to the tank with normal handling.

Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship, and appearance. Instrument calibration and method shall be as described in Test Method D Never set a tank upon a?

TOP Related Posts  DBX AFS 224 PDF

The thickness of the inner surface and interior layer 7.

The intent of these requirements is to avoid orienting joints asym reinforcing layers perpendicular to the maximum load-bearing direction circumferential. The combined thickness of the inner surface and interior layer shall not be less than 0. The clearance between the head shackle of the crane and the tank should be at least equal to the span between the lugs used for lifting.

Design Tanks stores resins in a climate-controlled storage area to eliminate production variances related s temperature changes.

Other techniques such as sprayed, wrapped, or overlaid? Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

The all-interior installation laminate placement is used only when the nozzle being installed has an integral conical gusset preventing application of an exterior laminate. NOTE 21—The use of organic reinforcing materials may reduce the Barcol hardness readings without necessarily indicating undercure.

Full protection must be provided when using chains or cables. As an alternative, a minimum of two passes of chopped roving of minimum length 0.

The Design Tanks Difference: Exceeding The Standards | Design Tanks

Damage caused by such action may result in cracking the inner corrosion-resistant liner, as well as the structural portion of the tank. NOTE 11—Tanks with unsupported bottoms require special design consideration. Where shape, thickness, or other restrictions preclude covering the 32999 with the preceding laminate, such cut edges and any machined?

NOTE 23—Practical test methods on samples cut from?